CFMCalc

Guide

What size air compressor for a nail gun

Nailers are rated per nail, so the answer depends on how fast you drive them.

Short answer

At a normal pace, brad and finish nailers run on any compressor, a 6 gallon pancake included. A framing nailer uses about 0.072 cu ft of air per nail, so a pancake delivering 2.6 SCFM keeps up with about 32 nails a minute and holds another 22 in its tank. For steady framing at 30 nails a minute with a margin, look for about 3.1 SCFM at 90 PSI; for two framing nailers on one hose, about 6.2.

Check your compressor against your nailers

How nailers are rated

A nail gun takes one gulp of air per nail and nothing in between, so its makers rate it in cubic feet of free air per drive (per cycle), not in CFM. SENCO explains it the same way: divide the air per cycle into a compressor's CFM and you get the nails per minute it can sustain. These are the figures in the manuals, all at 100 PSI:

  • 18 ga brad nailer: 0.04 cu ft per nail (Ridgid R213BNA manual: 0.04 cu ft per cycle).
  • 16 ga finish nailer: 0.045 cu ft per nail (DeWalt D51257 manual: 4.5 cu ft per 100 cycles).
  • 15 ga angled finish nailer: 0.06 cu ft per nail (DeWalt D51276 manual: 6.0 cu ft per 100 cycles).
  • Coil roofing nailer: 0.0415 cu ft per nail (DeWalt D51321 manual: 4.15 cu ft per 100 cycles).
  • Framing nailer: 0.072 cu ft per nail (DeWalt D51823 manual: 0.072 cu ft per shot).

Other models in each class are close but not identical, and your own nailer's manual has its figure in the specifications. Paslode's sizing formula is the one to use: nailers, times nails per minute each, times air per nail, times a safety factor. Paslode uses 1.2; the calculators here use 1.3, a 30 percent margin for leaks, hose and optimistic ratings.

Compressor needed by nailing pace

SCFM at 90 PSI the compressor should deliver for one nailer at 100 PSI, with a 30 percent margin
Nailer10 nails/min20 nails/min30 nails/min60 nails/min
18 ga brad nailer0.61.11.73.4
16 ga finish nailer0.61.31.93.8
15 ga angled finish nailer0.91.72.65.1
Coil roofing nailer0.61.21.83.5
Framing nailer1.02.13.16.2

Ten nails a minute is careful trim work with measuring between nails. Sixty is one a second without a break, which a roofing or framing crew reaches in bursts but rarely holds. The compressor chart's 2.2 CFM for a framing nailer is this same arithmetic at about 31 nails a minute. Two nailers on one compressor double the figure: two framers at 30 nails a minute each need about 6.2 SCFM, a 6.4 SCFM class machine.

What the tank adds

Nailing is bursty, so the tank does real work. The air stored between cut-out and cut-in pressure drives this many nails before the motor even starts:

Nails from a full tank down to cut-in pressure, motor off
CompressorPressure bandAir storedFraming nailsBrad nails
6 gallon pancake150 to 120 PSI1.6 cu ft2241
20 gallon150 to 120 PSI5.5 cu ft75136
30 gallon135 to 105 PSI8.2 cu ft113204

Once the motor is running it adds its own output. A framer driving a nail a second from a pancake delivering 2.6 SCFM uses air 1.9 cu ft a minute faster than the pump makes it, so the tank lasts about 50 seconds before the pressure falls below cut-in and keeps falling. Slow to 32 nails a minute and the same pancake keeps up indefinitely. That is why a pancake is enough for a deck or a shed and a frustration for a crew. An impact wrench is the opposite case: little air averaged over a job, but breaking lug nuts loose with the trigger held drains a pancake in under a minute.

Pressure costs air

A nailer set to a higher pressure uses more air per nail. Paslode lists its F-350S framing nailer at 0.082 cu ft per nail at 90 PSI and 0.108 at 120 PSI. The absolute-pressure arithmetic the calculator uses predicts 0.105 from the first figure, so the rule holds: set the regulator to the lowest pressure that sinks the nail flush, and the same compressor drives more nails a minute.

Frequently asked questions

Will a pancake compressor run a framing nailer?
Yes, for normal DIY pace. A 2.6 SCFM pancake keeps up with about 32 framing nails a minute and holds 22 more in its tank; at one nail a second it falls behind after about 50 seconds.
What size compressor do I need for a brad nailer?
Any of them. A brad nailer uses about 0.04 cu ft per nail, so even a small pancake sustains about 59 brads a minute.
What size compressor for a finish nailer?
A pancake or hot dog compressor. A 16 ga finish nailer at 30 nails a minute needs about 1.9 SCFM at 90 PSI with a margin, and a 15 ga angled nailer about 2.6.
What size air compressor for a roofing nailer?
About 1.8 SCFM at 90 PSI for one roofing nailer at 30 nails a minute, and 3.5 at a nail a second. Two roofing guns on one compressor double it.
How many CFM does a framing nailer use?
About 0.072 cu ft per nail, so 2.2 CFM at 30 nails a minute and 4.3 at 60, before any margin.
Can I run two nail guns off one compressor?
Yes, if the compressor covers both. Two framing nailers at 30 nails a minute each need about 6.2 SCFM at 90 PSI, which is more than a pancake delivers.
What PSI should a nail gun be set to?
Within the range on the tool, usually 70 to 120 PSI, and at the lowest setting that sets the nail flush. Higher pressure uses more air per nail.
Does tank size matter for a nail gun?
It sets how many nails you drive before the motor starts: about 22 framing nails from a 6 gallon tank and 113 from a 30 gallon. The pump's SCFM sets how fast you can keep going.

Work it out for your own project