CFMCalc

Guides

CFMCalc guides

Compressor sizing questions answered with the same demand model the calculators use.

Compressor size by job

What size compressor to paint a car

A full-size HVLP spray gun uses about 9 CFM without a break, so with the usual 30 percent margin the compressor has to deliver about 11.7 SCFM at 90 PSI: in practice a 14 SCFM machine, which usually means a 60 or 80 gallon, 240 volt compressor. Sanding the car with a dual action sander needs more, about 14.3 SCFM.

What size compressor for sandblasting

A small blast cabinet or pot blaster uses about 12 CFM at 90 PSI without a break, so the compressor needs to deliver about 15.6 SCFM with a margin: a 17.5 SCFM class machine, usually a two-stage 80 gallon or larger. Bigger nozzles use a lot more.

What size compressor for an impact wrench

A 1/2 in impact wrench draws about 4.5 CFM at 90 PSI while the trigger is held, but only in short bursts. A 20 to 30 gallon compressor delivering about 5.1 SCFM or more keeps up with lug nuts and suspension work; a 6 gallon pancake runs it for only about 52 seconds of continuous hammering before the pressure drops.

What size air compressor for a nail gun

At a normal pace, brad and finish nailers run on any compressor, a 6 gallon pancake included. A framing nailer uses about 0.072 cu ft of air per nail, so a pancake delivering 2.6 SCFM keeps up with about 32 nails a minute and holds another 22 in its tank. For steady framing at 30 nails a minute with a margin, look for about 3.1 SCFM at 90 PSI; for two framing nailers on one hose, about 6.2.

What size air compressor to blow out sprinklers

Size it from your largest zone's flow. Pushing a 10 GPM zone out at 50 PSI at its design flow takes about 5.9 SCFM of free air, so a 20 to 30 gallon compressor does it comfortably and a 6 gallon pancake does it in short bursts with waits to refill. Never exceed 80 PSI on PVC pipe or 50 PSI on polyethylene.

Frequently asked questions

What size air compressor do I need to paint a car?
A full-size HVLP spray gun uses about 9 CFM without a break, so with the usual 30 percent margin the compressor has to deliver about 11.7 SCFM at 90 PSI: in practice a 14 SCFM machine, which usually means a 60 or 80 gallon, 240 volt compressor. Sanding the car with a dual action sander needs more, about 14.3 SCFM.
What size air compressor do I need for sandblasting?
A small blast cabinet or pot blaster uses about 12 CFM at 90 PSI without a break, so the compressor needs to deliver about 15.6 SCFM with a margin: a 17.5 SCFM class machine, usually a two-stage 80 gallon or larger. Bigger nozzles use a lot more.
What size air compressor do I need for an impact wrench?
A 1/2 in impact wrench draws about 4.5 CFM at 90 PSI while the trigger is held, but only in short bursts. A 20 to 30 gallon compressor delivering about 5.1 SCFM or more keeps up with lug nuts and suspension work; a 6 gallon pancake runs it for only about 52 seconds of continuous hammering before the pressure drops.
What size air compressor do I need for a nail gun?
At a normal pace, brad and finish nailers run on any compressor, a 6 gallon pancake included. A framing nailer uses about 0.072 cu ft of air per nail, so a pancake delivering 2.6 SCFM keeps up with about 32 nails a minute and holds another 22 in its tank. For steady framing at 30 nails a minute with a margin, look for about 3.1 SCFM at 90 PSI; for two framing nailers on one hose, about 6.2.
What size air compressor do I need to blow out my sprinkler system?
Size it from your largest zone's flow. Pushing a 10 GPM zone out at 50 PSI at its design flow takes about 5.9 SCFM of free air, so a 20 to 30 gallon compressor does it comfortably and a 6 gallon pancake does it in short bursts with waits to refill. Never exceed 80 PSI on PVC pipe or 50 PSI on polyethylene.

Start here